UCDS Forum

polofox писал(а): 07 апр 2021, 20:54

fordsmaxtcdi писал(а): 07 апр 2021, 11:33 the files are in the wrong order and also the can-bus is wrong

2021-04-08 (2).png
as this ??

right,
enable SLEEP all modules and use a car battery charger of 8 -.... amps

fordsmaxtcdi писал(а): 07 апр 2021, 21:37

polofox писал(а): 07 апр 2021, 20:54

2021-04-08 (2).png
as this ??

right,
enable SLEEP all modules and use a car battery charger of 8 -.... amps

Thanks very much ,we will try it again

polofox писал(а): 07 апр 2021, 22:29

fordsmaxtcdi писал(а): 07 апр 2021, 21:37

right,
enable SLEEP all modules and use a car battery charger of 8 -.... amps

Thanks very much ,we will try it again

For 2018 Fusion/Mondeo:
(Bootloader): EJ7T-14C025-AA
JS7T-14C026-AJB
JS7T-14C026-BJB
JS7T-14C088-AJB
JS7T-14C088-BJB
- Firmware Build Date: October 30, 2017
firmware has the thick blue needles for gauges - digital speedometer moved to center

fordsmaxtcdi писал(а): 07 апр 2021, 22:37

polofox писал(а): 07 апр 2021, 22:29

Thanks very much ,we will try it again

For 2018 Fusion/Mondeo:
(Bootloader): EJ7T-14C025-AA
JS7T-14C026-AJB
JS7T-14C026-BJB
JS7T-14C088-AJB
JS7T-14C088-BJB
- Firmware Build Date: October 30, 2017
firmware has the thick blue needles for gauges - digital speedometer moved to center

My Car is Mondeo 2015 Titanium cd391,is ok?

yes but if you load the IPC configuration data, select the correct direct config type according to the module number

fordsmaxtcdi писал(а): 07 апр 2021, 22:46 yes but if you load the IPC configuration data, select the correct direct config type according to the module number

but all vbf has "Set new address failed."
my hardware is DP5T-14F094-CB

wrong order and HW=F113

fordsmaxtcdi писал(а): 08 апр 2021, 17:47 wrong order and HW=F113
123.png

Is that the right order?

yes try

fordsmaxtcdi писал(а): 08 апр 2021, 19:31yes try

00:00:00:509: Requesting hardware parts number...
00:00:00:767: F113 (HW) part number: DS7T-10849-CJR
00:00:00:769: F188 (SW) part number: DS7T-14C026-DJT
00:00:00:770: Loading and prepare database...
00:00:05:168: Searching for SEED keys...
00:00:05:170: SEED Keys found.
00:00:05:176: Programming mode OK!
00:00:06:179: Requesting protected mode...
00:00:06:190: Protected mode granted!
00:00:06:341: Loading Secondary Bootloader...
00:00:16:226: Secondary Bootloader successfully loaded and initialized.
00:00:16:535: Erasing flash...
00:00:16:537: Erasing flash block 1 from 2 ...
00:00:16:547: Erase Operation failed.
00:00:17:550: Failed to programming flash! Error: Request Out Of Range [0x31]
00:00:00:506: Requesting hardware parts number...
00:00:00:764: F113 (HW) part number: DS7T-10849-CJR
00:00:00:769: F188 (SW) part number: DS7T-14C026-DJT
00:00:00:779: Loading and prepare database...
00:00:05:017: Searching for SEED keys...
00:00:05:022: SEED Keys found.
00:00:05:038: Programming mode OK!
00:00:06:048: Requesting protected mode...
00:00:06:060: Protected mode granted!
00:00:06:212: Loading Secondary Bootloader...
00:00:16:102: Secondary Bootloader successfully loaded and initialized.
00:00:16:412: Erasing flash...
00:00:16:415: Erasing flash block 1 from 2 ...
00:00:16:421: Erase Operation failed.
00:00:17:424: Failed to programming flash! Error: Request Out Of Range [0x31】



It's still the same mistake.

I assume that your IPC has only 512kb ROM. It must be an very old IPC.

IPC photo

fordsmaxtcdi писал(а): 09 апр 2021, 17:34 IPC photo
123.png

Electronic instrument cluster photo
and new ucds ver.
viewtopic.php?f=3&t=4

fordsmaxtcdi писал(а): 09 апр 2021, 18:17 Electronic instrument cluster photo

as this?

UCDS IS V2.0.007.003